If you happen to have a kitchen hood that stops working, drafts poorly, makes noise, and doesn’t perform its functions, then it’s urgent that it be repaired. In this case, contact the Appliance Service Center. Breakage of such a device is usually difficult because the fundamental design of hoods has a rather complicated structure. Our company provides quality Hood Repair in Point Loma, CA.

Our company has been working on hood repair since 2001. Our Point Loma Hood Repair technicians have over 20 years of experience.

Causes of a soon-to-be-failed hood

Untimely cleaning of the grease trap filter. Clean it at least every 3 weeks if you cook for an average family daily. The charcoal filter, if present, should be completely replaced every six months, but it is usually placed where the hood has a recirculation version of the output of the trapped steam.

Operating the hood under a direct flame of the burners can also quickly damage the system.

A clogged ventilation system can put a lot of strain on hood operation.

Ideally, there should be a natural draft in the ventilation duct.

It’s important to remember to turn the hood on, a strong stream of greasy steam can quickly ruin a hood motor if it’s out of service at the time. Our experienced Hood Repair in Point Loma, CA technicians will quickly diagnose this problem.

Causes like this can easily take out the unit itself, the motor, and the electronics. Repair or at least clean it as soon as you notice anything wrong with it because it’s likely to worsen the operation of the hood and, for example, the motor may get stuck in grease and stop, and then it will simply burn out.

Main recommendations

• Keep an eye on the filters to prevent them from clogging. In modern and high-quality models there is a “pollution” indicator in the form of a light bulb or buzzer.
• Do not allow the hood to operate under an open flame, without utensils.
• Inspect the motor for grease build-up.

Main malfunctions and causes of damage

Weak draft

Steam is no longer drawn properly, you must check the filters, especially the grease trap filter, if it is clogged and prevents steam from exiting. You can check this by turning on the hood without filters. The filters should be cleaned and washed with special grease removers.

Bad drafts can also be due to other, less common reasons. Perhaps the ventilation duct at home is clogged with something. If you can’t fix the problem yourself, call Point Loma Hood Repairs.

Exhaust hood lighting is not working

The lighting system in most hoods is not complicated. You should start by inspecting the bulb itself and the socket contacts. Insert a known good bulb and immediately verify that the bulb itself is in good working order. If there are no faults, make sure that the extractor motor is working, if not, start from the socket and inspect all circuits and the switch panel (buttons). You can check the pads with a screwdriver, a tester or a light bulb. Our Hood Repair in Point Loma, CA technicians will fix the problem.

It makes a lot of noise when it’s running

Most cheap, low-quality hoods make a lot of noise due to the poor assembly of the unit. Even a small backlash and backlash during motor operation, can create a lot of vibration, buzzing and knocking. Over time, even in a good model, mounts come off and mechanisms are disturbed due to wear and tear. Contact our service center, Point Loma Hood Repair technicians will quickly fix any problems.

The hood doesn’t work at all

In such cases, the fan does not work, and the backlight does not turn on. Naturally it is necessary to check the source, make sure that there is voltage in the socket and then using a multimeter to check all the circuits in series, you must make sure that the voltage is on the plate or switch sites, possibly wire burned out or blown fuse, usually fusible. Hood Repair in Point Loma, CA will fix any problem you may have with your hood.

Hood repair works just like any other appliance. Major breakdowns come from broken wires and connection contacts. Motor windings often burn from jammed bearings and moving parts from corrosive grease.

Tracks on electronic control boards can flake off, capacitors can swell, or wires can simply break off. All of the above and many other hood failures can easily be fixed by an Appliance Service Center technician. Contact only the experienced technicians at Point Loma Hood Repair and Service. Our professionals will quickly find the breakdowns in your hood and fix them.