Ovens have recently become very popular, as it is easy and convenient to bake any food in them, because it is enough to set the temperature mode, cooking time and you can do other things. Breakdown of the oven occurs quite rarely, but still, it can happen at any time and thereby ruin all plans for a delicious lunch or dinner. In the event of a breakdown, contact the Appliance Service Center immediately. Our appliance repairmen at Thermador Oven Repair in San Diego County can help you fix oven breakdowns. Our technicians have over 20 years of experience. We have been in business since 2001.

The basic list of oven faults

Electric oven heats partially

So, you set the temperature, timer, and send the dish to bake, and upon completion you find that it is perfectly browned on top, but the bottom remains in its original form. This phenomenon indicates a possible oven heating element malfunction. In order to be sure that the heater is broken, turn off the appliance and give it time to cool completely.

Once the oven is cold turn it on and gently feel the bottom or the top (depending on which area the food is not baked), if the heating does not occur, then the heating element has burned out and needs to be replaced, this can be done by contacting the Thermador Oven Repair and Service.

The oven is not heating

If you have turned on your oven and noticed that it is not heating at all, but the light is on, pay attention to the heating indicator light, if it does not light up, most likely the problem is in the thermostat or the thermostat sensor. 

To repair the oven, you will need to replace the part. To do this, you need to remove the knob and unscrew the screws that fasten the thermostat. After that, remove the failed element and install a working one in its place. This repair will perform for you, our specialists Thermador Oven Repairs. 

Oxidation or burning of the terminal blocks 

This could be the result of prolonged and frequent use of the oven. The pads will need to be cleaned or replaced with new ones by Thermador Oven Repair and Service.

Wires inside the oven are burned or damaged

Wires could be burned due to voltage fluctuations, prolonged use of the oven, or improper maintenance. For example, if you do not regularly clean the inside of the appliance, a lot of grease builds up on it, which provokes overheating of the internal elements, as a result, the malfunction of the oven will not be long in coming. In addition, if the oven is connected without grounding, the wiring may have been damaged by a lightning storm.  Our Thermador Oven Repair electrical repair technicians will fix the breakdowns quickly and on time.

Failure of the electronic control module

If the electronic control module is malfunctioning, the oven must be disassembled, and the element dismantled. After a diagnosis, the Thermador Oven Repairs and Services technician will decide how to fix the problem. In some cases, the part is reflated. 

If any part in the module is burned out (capacitor, chip, fuse, controller or other) repair is not carried out, the problem is solved only by replacing the control board. It should be noted that for the replacement of this part, it is best to contact our service center. 

The oven overheats

If you set the desired temperature and cooking time, but at the end of the process you find that the product has remained raw, overcooked or over dried, most likely the oven heats too much or vice versa – not enough. 

The fact is that the electric oven has a thermostat that is responsible for adjusting the temperature. It is the thermostat that controls the heating of the heating elements and turns them off at the right moment. If the food burns or does not bake, but the cooking mode is set correctly, the reason lies in the faulty thermostat. It will be necessary to replace the part with a functioning one, for this purpose it is better to contact a Thermador Oven Repair technician.

For complicated oven failure situations, contact a certified Appliance Service Center. Thermador Oven Repair and Service employees undergo special training and pass an exam for knowledge of the peculiarities of a particular brand of appliances. It is also advantageous to go to a service center because they are sure to be able to find the parts you need for repairs.